AEM 5772 Antimicrobial

AEM 5772 Antimicrobial

CAS No: 27668-52-6

Active Ingredient: 3-(trimethoxysilyl) propyldimethyloctadecyl ammonium chloride 72% in Methanol solution

A SILANE QUATERNARY AMMONIUM SALT

EPA Reg. No. 64881-2

Composition:
ACTIVE INGREDIENT: 3-(trimethoxysilyl) propyldimethyloctadecyl ammonium chloride .................. 72%
INERT INGREDIENTS ..................................................................................28%
TOTAL ..............................................................................................100%

PRODUCT FEATURES AND BENEFITS
AEM 5772 Antimicrobial imparts durable biostatic activity to the surface of a wide variety of substrates.
AEM 5772 Antimicrobial is effective against mold, mildew and algae as a static agent.
Increased efficiency – through proper application, durable bacteriostatic, fungistatic and algistatic surfaces can be
attained with a minimum amount of AEM 5772 Antimicrobial.
Provides freshness and combats deterioration and discoloration caused by bacteria, fungi and algae.

HAZARD TO HUMANS AND DOMESTIC ANIMALS.
DANGER! CORROSIVE. CONTAINS 12% METHANOL. CAUSES IRREVERSIBLE EYE DAMAGE AND SKIN IRRITATION.
MAY BE FATAL IF INHALED. Methanol may cause blindness. May be harmful if swallowed or absorbed through the skin. Do not
get in eyes, on skin, or on clothing. Wear protective eyewear, rubber gloves, and protective clothing. Do not breathe vapor. Wear a
NIOSH approved respirator with any N, R, P, or HE filter. Appropriate measures should be taken to prevent the accumulation of
hazardous concentrations of methanol vapors in the work area. Wash thoroughly with soap and water after handling and before
eating, drinking, using tobacco, chewing gum or using the toilet. Remove and wash contaminated clothing before reuse.

ENVIRONMENTAL HAZARDS:
This pesticide is toxic to fish and aquatic invertebrates. Do not discharge effluent containing this product into lakes, streams,
ponds, estuaries, oceans or other waters unless in accordance with the requirements of a National Pollutant Discharge Elimination
System (NPDES) permit and the permitting authority has been notified in writing prior to discharge. Do not discharge effluent containing
this product to sewer systems without previously notifying the local sewage treatment plant authority. For guidance contact your State
Water Board or Regional Office of the EPA.
Every effort should be made to contain accidental spills of concentrate to the immediate area. This may be accomplished by the
use of sandbags or barrier material to confine the spill to facilitate cleanup and disposal. Contaminated sand or barrier material may
then be disposed of by burial in an approved landfill. Many spills may be cleaned up with rags or other absorbent materials by wiping,
soaking and/or mopping and allowing the liquid to absorb onto the material. The absorbent material may then be disposed of by
incineration or landfill. Floor drains in areas of material use should be protected with absorbent material or barrier material to contain
accidental spills.
Inactivation of solutions containing AEM 5772 Antimicrobial may be accomplished by addition of an anionic surfactant, or detergent
in quantity equivalent to that of AEM 5772 Antimicrobial in solution.
PHYSICAL OR CHEMICAL HAZARDS
Flammable. Keep away from heat and open flame

Comment

related information

PHMB 98% powder,Polyhexamethylene biguanide hydrochloride 98% powder

2021-08-20 Disinfectant

PHMB 98% powder,Polyhexamethylene biguanide hydrochloride 98% powder PHMB 98% powder (Polyhexanide,polyhexamethylene biguanide) is a polymer used as a disinfectant and antiseptic. Synonyms: antimicrobial polymer PHMB,Polyhexanide (PHMB),pol…

FAQ of SD Labs’s products, SD 90, SD 90+

2021-08-13 Disinfectant

FAQ of SD Labs's products, SD 90, SD 90+ Q. Where and how are SD Labs’ products manufactured? A. Our products are manufactured in the USA in a EPA registered facility under strict quality controls. Q. What are SD Labs’ SD 90 and 90+ product…

SD 90+ EnviroShield ENDURE

2021-08-13 Disinfectant

SD 90+ EnviroShield ENDURE SD 90+ EnviroShield ENDURE is clear, ready to use spray-on coating that, when properly applied, bonds to a surface at the molecular level, leaving a protected antimicrobial coating on the surface that can last for…

SafeTouch / Biosafe HM 4100 Antimicrobial

2021-08-11 Disinfectant

SafeTouch / Biosafe HM 4100 Antimicrobial what is SafeTouch and is it safe to use? When we consider an antimicrobial that is EPA registered (Biosafe HM 4100 Antimicrobial with EPA Registration Number: 83019-1, cas no 199111-50-7) we can be …

Antimicrobial Masterbatch SafeTouch by PolyFusion

2021-08-11 Disinfectant

Non-Leaching,Non-Toxic Antimicrobial Masterbatch SafeTouch by PolyFusion PolyFusion, LLC has recently introduced an antimicrobial master batch for thermoplastics.The master batch is being marketed under the name of SafeTouch® and remains ef…

SD Labs, EPA, DTN 100 Antimicrobial

2021-07-30 Disinfectant

How Does SD 90+ Work

2021-07-28 Disinfectant

What is SD 90+ (EnviroShield ENDURE)

2021-07-28 Disinfectant